INTAKE

[fiat218]

i changed out the intake manifold,
what i have is a 80 with smog, now that i removed all this and the intake .what do i do with the 2 hose coming from the canister? and there one from the brake booster? and then i believe there is a return gas line! and do i plug the exhaust port that does not get coverd with the single plane manifold ? or leave it open

let me know. thanks

[Kent124]

.what do i do with the 2 hose coming from the canister?

Disconnect hoses from canister and install caps over the canister nipples. You can find these at places like AutoZone.

and there one from the brake booster?

Intake should have a large connection to hook this to.

and then i believe there is a return gas line!

Most people cap since there is no provision for this on DFEV.

do i plug the exhaust port that does not get covered with the single plane manifold ?

If you are running a stock exhaust manifold and don't enjoy the smell of exhaust you have two options: plug the cross over port on the intake side or install a blanking plate on the exhaust side. Personally I would look for a FI exhaust manifold and down pipe to install.

[fiat218]

does the brake booster go to this
the photo shows the nipples on the intake . i assume u attach it to one of the
m and block the other end or no?

[fiat218]

.what do i do with the 2 hose coming from the canister?

Disconnect hoses from canister and install caps over the canister nipples. You can find these at places like AutoZone.

and there one from the brake booster?

Intake should have a large connection to hook this to.

and then i believe there is a return gas line!

Most people cap since there is no provision for this on DFEV.

do i plug the exhaust port that does not get covered with the single plane manifold ?

If you are running a stock exhaust manifold and don't enjoy the smell of exhaust you have two options: plug the cross over port on the intake side or install a blanking plate on the exhaust side. Personally I would look for a FI exhaust manifold and down pipe to install.

CANISTER? can i remove it and block off the hose going into the bottom? or do as u say , cap off the top

[jsab]

Yes, brake booster goes to that fitting on the manifold. You can remove the canister and plug the hoses, or leave one unplugged for a tank vent hose.

[fiat218]

thanks to the both of you for replying

[124JOE]

this is perfect

do i leave the top one or the side one open for a vent?
on the canister

[jsab]

I think it is the side one.

[Kent124]

I think it is the side one.

I left the top open. The ones on the bottom in my 1979 are a tee fitting. This means the fumes from the gas tank vent would simply flow in one side of the fitting and out the other side defeating the purpose of the canister. Just my 2 cents.

[jsab]

I think it is the side one.

I left the top open. The ones on the bottom in my 1979 are a tee fitting. This means the fumes from the gas tank vent would simply flow in one side of the fitting and out the other side defeating the purpose of the canister. Just my 2 cents.

I just eliminated the canister, left the bottom hose for the vent.

[124JOE]

if i do that should i stick some steel wool up the hose as a flame stop?

[jsab]

That's a good idea, I didn't think of that....
I lengthened the hose, it terminates just outside of the opening where the original fresh air duct was, and I put a small filter on it to keep any crap out.

-John

[fiat218]

the water line,? i am thinking it was for the choke !!! anyways what do i do with that? just plug it off?

[124JOE]

no the vent line coming from the gas tank

the water line i looped to the intake

but if your intake dosent have a nipple near the fire wall then plug it

[fiat218]

it does not have a inlet, that i know of. there is two holes but there where plugged so i will just plug off this water hose